Skip to content
F-Line Hydraulic FittingsDIN 2353 · ISO 8434-1
F-Line TECHNICAL GUIDE

DIN 2353 Fitting Installation and Inspection Overview

Successful cutting-ring connections depend on suitable tubing, matched components, careful preparation and the correct assembly procedure for the supplied fitting system.

ISO 8434-1 is the equivalent international standard for DIN 2353 24° cone tube connections.

5 October 2026 · Fluidline technical reference

Page updated · Fluidline Products (Pty) Ltd

Rigid hydraulic tubes secured with clamps and connected to flexible hose assemblies
Supported hydraulic tube runs with hose connections. Application photograph.
INSIDE THE CONNECTION

How the Components Fit Together

Explore the tube, nut, cutting ring and fitting body in an exploded view and a section through the assembly.

DIN 2353 connection diagram showing the tube, nut, cutting ring and fitting body separately, a completed assembly, and a cutaway with the 24-degree cone seat labelled.
DIN 2353 bite-type connection — component overview.Open full-size diagram ↗Download diagram ↓
UNDERSTAND THE CONNECTION

DIN 2353 vs Uni-Lok Twin Ferrule Tube Fittings

A DIN 2353 cutting-ring connection uses one cutting ring between the nut and body. Fluidline supplies Uni-Lok twin ferrule tube fittings, which use separate front and back ferrules. These are different connection systems: select the complete matched assembly for the application.

Cutting-ring and twin-ferrule designs
FeatureDIN 2353 cutting-ring connectionUni-Lok twin ferrule tube fittings
Components around the tubeOne cutting ring and a union nut, used with a matching 24° body seat.Separate front and back ferrules, a nut and the matching fitting body.
Operating principleThe nut drives the cutting ring onto the tube during the specified assembly procedure.The two ferrules work together to form the tube seal and grip; their precise action depends on the design.
How to specifyTube OD, LL/L/S series, material, ring system and all connection details.Tube OD, material, Uni-Lok fitting series and all connection details.
Assembly instructionsUse the supplied cutting-ring system instructions and its inspection method.Use the supplied Uni-Lok assembly instructions and inspection method.
Parts substitutionDo not replace its ring with a twin-ferrule set.Do not replace its ferrules with a DIN cutting ring.

One Ring Does Not Mean One Cutting Edge

“Single ferrule” describes the number of separate ring components. A ring may have more than one cutting edge. Count and identify the components using the supplied product drawing, rather than inferring the design from marketing terminology.

Neither ferrule count nor the term “compression fitting” establishes a universal pressure rating or suitability for a particular fluid. Confirm the exact fitting, tubing, material, temperature limits and assembly requirements.

Fluidline’s twin ferrule brand: Uni-Lok twin ferrule tube fittings. For the DIN 2353 connection standard, see the ISO 8434-1 scope. Use matched components and the instructions for the selected fitting system.

Cutting-ring part numbers and dimensions →
Matching tube nuts →
L and S series comparison →

Prepare the Work and Confirm the Components

Before opening a hydraulic connection, isolate the equipment and release stored pressure using the equipment procedure. Consider accumulators, supported loads and trapped fluid. Never loosen or retighten a fitting while it is pressurised. Keep the work area clean and protect open ports and tube ends against contamination.

Check the fitting configuration, tube outside diameter, LL/L/S series, tube wall and material before assembly. Confirm that the body, nut, cutting ring and any seals form an approved combination. Inspect the threads and sealing surfaces for damage. Obtain the assembly instructions for the supplied system, including any requirements for tools, lubrication, preassembly and inspection.

    Prepare and Support the Tube

    Cut the tube square using the equipment specified for the system. Remove internal and external burrs without creating an excessive bevel, then clean away chips and debris. Check that the tube end is round, straight and undamaged over the length needed for assembly. Confirm the minimum straight length near a bend before cutting the tube.

    Use tubing that meets the specified dimensional, material and hardness requirements. Where support sleeves are required, select the approved size and type. Route the tube so the connection can be assembled without forcing misaligned parts together. Fit suitable tube supports to manage vibration and avoid leaving the fitting to carry unnecessary mechanical loads.

      Follow the Supplied Assembly Method

      Place the nut and cutting ring on the tube in the correct orientation. Keep the tube firmly against the specified stop during the cutting-ring operation. Use the prescribed preassembly tool or machine where required, particularly when the instructions specify this for stainless steel, larger sizes or a particular connection design.

      Apply lubrication only as directed for the components and assembly method. Surface finishes and materials can change friction and tightening behaviour. Use the stated inspection method to confirm that the ring has formed correctly and retained the tube. A visible material collar may be part of a conventional cutting-ring inspection, while other sealing systems use different checks.

      Complete the joint using the specified final assembly procedure and hold the body as instructed. There is no single tightening torque or number of turns that applies to every DIN 2353 fitting. Manual preassembly, machine preassembly and different ring designs can require different final assembly steps.

        Inspect, Commission and Maintain the Connection

        After assembly, check the installation for alignment, support, clearance and cleanliness. Commission and inspect for leakage using the equipment and site procedures. Keep hands away from suspected hydraulic leaks: a small pressurised jet can cause serious injury. If a connection needs correction, isolate and depressurise the system first.

        During maintenance, protect dismantled parts and inspect the tube end, ring, nut, body and seals. Replace damaged or unsuitable components. Preserve matched assemblies where the supplied instructions require this, and use the specified reassembly procedure. Reuse depends on component condition and system instructions; repeated disassembly does not justify an unlimited service-life assumption.

        • Confirm the tube, series and complete component combination before assembly.
        • Use the specified tools and inspection criteria; check tools for wear.
        • Retain the supplied assembly instructions with maintenance records.

        Questions Answered

        How many turns should I tighten a DIN 2353 nut?

        Use the instructions for the supplied fitting system and assembly method. The correct procedure depends on the ring design, material, size and whether preassembly was manual or by machine.

        Can I reuse a cutting-ring tube connection?

        Reassembly may be permitted after inspection, subject to the supplied system instructions. Check all components for damage and follow its reassembly method rather than repeating an assumed first-assembly turn count.

        Does a single cutting ring mean a single cutting edge?

        No. Single ferrule describes one separate ring component. Its cutting-edge design depends on the supplied system; identify it from the product drawing and assembly instructions.

        Can DIN cutting-ring and twin-ferrule components be mixed?

        Do not substitute components between these systems. Select the complete matched assembly and obtain confirmation for the exact connection, tubing and operating duty.

        SPECIFY YOUR CONNECTION

        Request the Right Fitting

        Send the connection details and operating conditions. Fluidline can confirm the supplied configuration, availability and supporting documentation with your quotation.

        +27 11 312 9339
        ram@fluidline.co.za · brett@fluidline.co.za

        Fluidline Products (Pty) Ltd
        Unit 4 Acacia Park, Capital Hill Commercial Estate, Le Roux Avenue, Midrand, 1685, South Africa
        Fluidline contact details →
        DIN Fittings and Technical Enquiries

        Send your enquiry directly. We save your requirements and email Brett and Ram so they can respond. Privacy information.